twu
01-10-2000, 03:37 PM
hi, a newbies question.
I have lawp 4.04. running on a celeron 300a with 192 ram and a darla 24.
From the audio driver menu, i can see that they are several driver choice
i have.
asio mme
asio direct x
echo/layla/darla/gina
mme for sblive
...etc
So the first thing i did was choosing the echo/layla/darl/gina driver. and
relauch the application. when clicking the control panel, the only thing
shows was a dialog box says allow asio 2 monitoring. no other choice.
everything seems to be working, i can choose any output port i want ...etc.
Then i realize that i would like to use GIGA at the same time. And of
course i have turn on the multiclient audio function in darla 24 (5.02
driver). However, GIGA says the audio device is being used. Then i
realize that during the days i was using cakewalk 9.0 audio, i needed to
disable the output drivers i don\'t need, thus free the output for GIGA.
Everything is working.
But now, in logic, there is no place for me to choose which port to active
or not when choosing echo/layla/darla/gina driver, it just ate all the
output ports.
So i thought maybe i can try the asio mme driver. I ran the logic audio
setup program, tested everythings, everyport shows up in the dialog, ran
the simulation ..etc. This time in the control panel, i can see and choose
the port i want, and set the sync preference. When i play back in logic, i
can see at the audio mixer the meter is running, saying everything is
working good, however, i don\'t hear anything coming out of spearker. I
check the echo mixer panel, and sure enough, no signal is going to the
output port, thus no sound. It seems like logic is not communication from
the master output to the sound card correctly.
I then try asio direct x. Everything works fine, however, this is only for
playback, plus it won\'t work for 24 bit recording, so that is out of the
question.
So would someone please help, THANKS
I have lawp 4.04. running on a celeron 300a with 192 ram and a darla 24.
From the audio driver menu, i can see that they are several driver choice
i have.
asio mme
asio direct x
echo/layla/darla/gina
mme for sblive
...etc
So the first thing i did was choosing the echo/layla/darl/gina driver. and
relauch the application. when clicking the control panel, the only thing
shows was a dialog box says allow asio 2 monitoring. no other choice.
everything seems to be working, i can choose any output port i want ...etc.
Then i realize that i would like to use GIGA at the same time. And of
course i have turn on the multiclient audio function in darla 24 (5.02
driver). However, GIGA says the audio device is being used. Then i
realize that during the days i was using cakewalk 9.0 audio, i needed to
disable the output drivers i don\'t need, thus free the output for GIGA.
Everything is working.
But now, in logic, there is no place for me to choose which port to active
or not when choosing echo/layla/darla/gina driver, it just ate all the
output ports.
So i thought maybe i can try the asio mme driver. I ran the logic audio
setup program, tested everythings, everyport shows up in the dialog, ran
the simulation ..etc. This time in the control panel, i can see and choose
the port i want, and set the sync preference. When i play back in logic, i
can see at the audio mixer the meter is running, saying everything is
working good, however, i don\'t hear anything coming out of spearker. I
check the echo mixer panel, and sure enough, no signal is going to the
output port, thus no sound. It seems like logic is not communication from
the master output to the sound card correctly.
I then try asio direct x. Everything works fine, however, this is only for
playback, plus it won\'t work for 24 bit recording, so that is out of the
question.
So would someone please help, THANKS