GigaStudio and the Dakota card....

[studio77]

I am trying to use Gigastudio with the Frontier Dakota Card. The problem is Gigastudio will not map through the Dakota card and will not recognize the Dakota card in the View/Settings/Hardware-Routing. When I run the Diagnostics test it recognizes the card but shows that it doesn\'t \"map\" through the card.

The Dakota works with other programs flawlessly and it also worked with Gigasampler 1.6. I have since done a fresh install of Win98se and have only loaded Gigastudio.

Here is part of the diagnostic read-out that seems to concern me:

GigaStudio kernel: Loaded!!!
GigaStudio driver: Has ENABLED kernel.
Status code: 1030000, GigaStudio is properly configured.
Hw. config.: Status = 1030000, Type = HWTYPE_DSOUNDIF, ID = CARDID_GENERIC
Fs hw = 44100, Fs eng = 44100, chan/Output = 2, bits/sample = 16
Testing driver mapping ...
User mode Drv S 1:2 Dakota, did NOT map.
User mode Drv A 1:2 Dakota, did NOT map.
User mode Drv A 3:4 Dakota, did NOT map.
User mode Drv A 5:6 Dakota, did NOT map.
User mode Drv A 7:8 Dakota, did NOT map.
User mode Drv B 1:2 Dakota, did NOT map.
User mode Drv B 3:4 Dakota, did NOT map.
User mode Drv B 5:6 Dakota, did NOT map.
User mode Drv B 7:8 Dakota, did NOT map.
GigaCompatible hardware:
GSIF Compatible cards: 1 cards currently active.
Frontier Design Dakota : 16 outputs supportted.


Thanks


Don

[Mattifer]

I don\'t know if this will help or not, but on my system (Dakota, GS, Reaktor, CW9), I\'ve found that if I have any other prog claiming out ports (namely, Reaktor using ASIO), those which are selected become unavailable in GS, and vice-versa.

According to frontier, while you CAN simultaneously use both GSIF and ASIO together, they cannot be applied on the same i/o.

Hope this helps,
Mattifer

[LHong]

Well, I have same problems here too. what does it mean?
\"...
==================================== GigaSampler Info =================================
Gigasampler kernel: Loaded!!!
Gigasampler driver: Has ENABLED kernel.
Status code: 3170000, Gigasampler is properly configured.
Hw. config.: Status = 0, Type = HWTYPE_DSOUNDIF, ID = CARDID_GENERIC
Fs hw = 0, Fs eng = 0, chan/Output = 0, bits/sample = 0
Testing driver mapping ...
User mode Drv Pulsar Play 1, did NOT map.
User mode Drv Pulsar Play 2, did NOT map.
User mode Drv Pulsar Play 3, did NOT map.
User mode Drv Pulsar Play 4, did NOT map.
User mode Drv Pulsar Play 5, did NOT map.
User mode Drv Pulsar Play 6, did NOT map.
User mode Drv Pulsar Play 7, did NOT map.
User mode Drv Pulsar Play 8, did NOT map.
User mode Drv Pulsar Play 9, did NOT map.
User mode Drv Pulsar Play 10, did NOT map.
User mode Drv Pulsar Play 11, did NOT map.
User mode Drv Pulsar Play 12, did NOT map.
User mode Drv Pulsar Play 13, did NOT map.
User mode Drv Pulsar Play 14, did NOT map.
User mode Drv Pulsar Play 15, did NOT map.
User mode Drv Pulsar Play 16, did NOT map.
GigaCompatible hardware:
Aark 20/20 Drv: Not installed!
...\"
Regards,
LHong

[studio77]

LHong,

Did you ever resolve this problem?

Thanks for any help!


Don